无线测温仪AN200型钢水铁水铜水测温仪

炉前高精度钢铁水熔炼炉钢水，铁水，铜水锌水微机智能测温仪型钢水铁水铜水测温仪无线测温仪AN200型钢水铁水铜水测温仪

1 简介
本测温仪以高速16位嵌入式微处理器为核心。采用了自动校准电路，采用精密的温度传感器对冷端温度进行测量，并可以进行软件校正。在数据采集上采用高精度AD转换芯片，采样周期为20ms，对空间的工频有很强的抗干扰性。
本测温仪可适用于炼钢、炼铝、铸铁等行业中溶液温度的测量，也可以测量炉渣温度。
2 功能说明
? DC12V有源喇叭输出接口√
? RS485串行通讯接口（订货特殊说明）
? 微型打印机接口（订货特殊说明）
? RS232异步串行通讯接口（订货特殊说明）
? 带隔离的BCD码输出接口（订货特殊说明）
? 模拟量4~20mA输出接口（订货特殊说明）√
? 30条历史测试数据存储（如需存储更多得历史测试数据，订货时特殊说明）√
? 语音报数（订货特殊说明）
3 技术参数
热电偶型号 S B R WRe3/25
快速测温范围 1000~1769℃ 1000~1820℃ 1000~1769℃ 1000~1999℃
连续测温范围 100~1769℃ 500~1820℃ 100~1769℃ 100~1999℃
显示方式 3位半5英寸高亮度红色LED，字高127mm
工作环境 温度0~55℃；相对湿度<85%
存储环境 温度-40~85℃；相对湿度<95%
电源 AC220V/50Hz，功耗20W
尺寸 400mm×300mm×110mm

精炼炉专用大屏幕微机钢水测温仪高温2000度铜水，钢水液体厂家

1 Introduction

The temperature measuring instrument with high speed 16 bit embedded microprocessor core. Using the automatic calibration circuit, using the measurement of the temperature of cold end temperature sensor precision, and can be a software correction. Using high precision AD conversion chip in data acquisition, the sampling period is 20ms, the frequency of space has very strong anti interference.

Measurement of the temperature measuring instrument can be applied to the solution temperature, aluminum, cast iron steel industry, also can measure the temperature of slag.

2 Function

Ø DC12V speaker output interface√

Ø RS485 Serial communication interface（When ordering special instructions）

Ø miniature printer interface（When ordering special instructions）

Ø RS485 Serial communication interface（When ordering special instructions）

Ø An output interface of BCD code is with isolation（When ordering special instructions）

Ø the analog 4~20mA output interface（When ordering special instructions）

Ø the 200 historical test data storage√

Ø Be speech sound（When ordering special instructions）

3 Technical parameters

4 Panel

The panel is provided with a three measurement indicator: preparation, measurement, end, and three key：K1、K2 and K3。

5 Indicator lights and alarm horn control output instructions

In the absence of measurement is not yet inserted thermocouple temperature measurement instrument, display the current time, the three lights are not bright, insert the thermocouple after the green light, the thermocouple is inserted into the molten steel after the yellow light, when measured after the success of the red light, at the same time the alarm output control.

After testing the test results show that 180 minutes 5 seconds, horn, trumpet for active DC12V output. Schematic wiring as shown below:

6 Set key and dial the specific operating instructions

There are three key K1, K2 and K3 in the thermometer on the front panel is used to set the date, time and operation parameters. The K1 key is used to select parameters to set (the specific item number shown in the table below), the K2 is used to select the set position, K3 is used to input a specific parameter value.